3.6×10mm 快断保险丝 UL CSA CQC 100mA-10A 125V/250V
1.規格型號和安規認證
model number and safety certification
品名規格：系列號+額定電流+額定電壓+認證符號
model number: part number+rated current+rated voltage+approvals.
例子[example]:
3gfu， 2a， 125v/250v
1)系列號 part number，2)額定電流 rated current，3)額定電壓 rated voltage
1-2 額定電流和額定電壓 rated current and voltage
額定電流：100ma~10a rated current: 100ma~10a
額定電壓：250v ac rated voltage:250v ac
1-3 標示 marking
保險絲上需有下列標示 the fuse shall have the following marking:
規格：特性符號+額定電流+額定電壓 specification:characteristic symbol+rated voltage
100ma~800ma : _ma125v/250v 1a~10a: _a125v/250v
trade mark:the manufacture’s logo+part number+approvals
100ma~10a:
注意：對標示字樣大小沒有規定
note:size of the markings have not be specified.
2.適用範圍 scope
適用於一般電子設備。used in electronic equipment.
3.工程圖和結構 outline drawing and structure
3-1 工程圖（單位：mm）outline drawing and dimensions(unit:mm)
3-2 結構 structure
編號no.
元件component
材質material
數量quantity
1
熔絲 wire
合金 alloy
1
2
銅帽 cap
黃銅鍍鎳 brass with mickel plated
2
3
本體 body
玻璃管 glass tube
1
4
引線 lead
鍍錫銅線 tinned copper wire
2
4.外觀及形狀；appe***nces and configuration
4-1 外觀：不應有破碎、明顯的汙斑；appearances:there shall no fragmentation and of remarkable blotch.
4-2 形狀：帶腳的保險絲；configuration:axial leaded fuse.
5.物理特性；physical ch***cteristic
5-1 拉力測試;沿端子的軸向施加 10n 的拉力，持續 1 分鐘。
tensile test;keep pulling the cap of the fuse with 10n at axial
6.電氣特性
electrical ch***cteristics
熔斷/電流特性：
acting time/current characteristic
a、breaking capacity（分断能力）(time lag and fast acting)
50a 250v ac
b、electrical characteristics
time lag
rated current
% of ampere
opening rating time
100ma~ 10a
100%
200%
4 hours, minimum
5 seconds, max.
c、temperature character
当100%的电流下温度上升不超过75℃
when 100% of rating the temperature rise doesn’t exceed 75℃.
average time current curves.
7.環境特性
environmental specification
7-1 操作溫度範圍：-5℃~60℃
operating temperature: -5℃~60℃
7-2 保存條件
storage conditions
溫度：+10℃~60℃
temperature: +10℃~60℃
在相對濕度≤75%下平均可存放3年
on average, it can be stored below the relative humidity or 75% for 3 years.
在非露天下，相對濕度為95%下多可存放30天。
without dew, it can be kept under humidity of 95% for 30 days.
8.焊接條件
soldering paameters
8-1波峰焊
wave solder
焊接溫度：260±5℃
soldering temperature:260±5℃
焊接時間：4 sec. max.
soldering time:4 sec.max.
8-2手工焊錫
manual solder
焊接溫度：350±5℃
soldering temperature: 350±5℃
焊接時間：3 sec. max.
soldering time: 3 sec. max.
9.其他使用注意事項
other notice in using
如果需在保險絲上加熱縮套管，烘烤溫度與時間需參照以下規定
if heat shrink tubing was needed,the roast temperature and time should be refer to the following.
設定烘烤溫度：不大於150℃ 烘烤時間：50s max.
the temperature should be sel under 150℃,roast time:50s max.
